Skip to content

Add Parade PS195 bridge support to enable HDMI on Glymur/Mahua/Kalambo CRDs - #1493

Open
nabix (naala-qcom) wants to merge 5 commits into
qualcomm-linux:qcom-7.3from
naala-qcom:hdmi-7.3
Open

nabix (naala-qcom) wants to merge 5 commits into
qualcomm-linux:qcom-7.3from
naala-qcom:hdmi-7.3

Conversation

@naala-qcom

Copy link
Copy Markdown

This series adds initial Linux support for the Parade PS195 DP-to-HDMI
bridge and uses it to enable HDMI on the Qualcomm Glymur CRD family
(Glymur CoB/SiP, Mahua, and Kalambo).

Link: https://lore.kernel.org/all/20261112-mahua-hdmi-v1-0-b463d7b1dd7e@oss.qualcomm.com/#r

Backport:
qualcomm-linux/kernel-topics#2261
qualcomm-linux/kernel-topics#2262

Note: This series also Backport the minimal changes needed to apply the above HDMI series changes from the following upstream series.
https://lore.kernel.org/all/20261106-topic-sip_cob-v3-1-52cd3826ab49@oss.qualcomm.com/

quic-kdybcio and others added 5 commits November 19, 2026 17:42
Backport the minimum required changes from the deps series
(20261106-topic-sip_cob-v3-0-52cd3826ab49@oss.qualcomm.com)
to allow the mahua-hdmi PS195 bridge series to apply cleanly:

- Rename vreg_l18b_e0_1p2 -> vreg_l18b0 and vreg_l4c_e1_0p72 ->
  vreg_l4c1 in glymur-crd.dtsi and glymur-qcb.dts to unify
  regulator handles across Glymur board files [from deps patch 1/8:
  Unify Glymur/Mahua regulator handles]

- Update all vreg_l18b0 consumer references (vdd-io-supply on
  woofer/tweeter speakers and WCD codec) in glymur-crd.dtsi

- Add &usb_2_qmpphy supply properties (vdda-phy-supply = vreg_l4c1,
  vdda-pll-supply and refgen-supply = vreg_l4f_e1_1p08) in
  glymur-crd.dtsi needed by the QMP PHY driver for the PS195
  DP2-to-HDMI path [from deps series base tree]

Link: https://lore.kernel.org/all/20261106-topic-sip_cob-v3-1-52cd3826ab49@oss.qualcomm.com/
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Nabige Aala <nabige.aala@oss.qualcomm.com>
Add bindings for the Parade PS195 DisplayPort to HDMI bridge, describing
its power supplies, optional reset GPIO and display ports.

Link: https://lore.kernel.org/all/20261112-mahua-hdmi-v1-1-b463d7b1dd7e@oss.qualcomm.com/
Signed-off-by: Mahadevan P <mahadevan.p@oss.qualcomm.com>
Signed-off-by: Nabige Aala <nabige.aala@oss.qualcomm.com>
The Parade PS195 is a DisplayPort to HDMI converter that runs firmware
from external SPI flash. Add a platform bridge driver to sequence its
power supplies and optional reset GPIO.

Keep the bridge powered for AUX and HPD handling between modesets. Use
late suspend and early resume to order power transitions around the
display controller.

Link: https://lore.kernel.org/all/20261112-mahua-hdmi-v1-2-b463d7b1dd7e@oss.qualcomm.com/
Signed-off-by: Mahadevan P <mahadevan.p@oss.qualcomm.com>
Signed-off-by: Nabige Aala <nabige.aala@oss.qualcomm.com>
Enable the PS195 bridge driver as a module for HDMI output on Glymur,
Mahua and Kalambo CRDs.

Link: https://lore.kernel.org/all/20261112-mahua-hdmi-v1-3-b463d7b1dd7e@oss.qualcomm.com/
Signed-off-by: Mahadevan P <mahadevan.p@oss.qualcomm.com>
Signed-off-by: Nabige Aala <nabige.aala@oss.qualcomm.com>
Enable the PS195 HDMI path on Glymur CoB/SiP, Mahua and Kalambo CRDs
through their shared glymur-crd.dtsi.

Describe the bridge, connector, supplies and four-lane DP2 connection
through the USB2 QMP combo PHY. Add the GPIO126 HPD state to glymur.dtsi.

Link: https://lore.kernel.org/all/20261112-mahua-hdmi-v1-4-b463d7b1dd7e@oss.qualcomm.com/
Signed-off-by: Mahadevan P <mahadevan.p@oss.qualcomm.com>
Signed-off-by: Nabige Aala <nabige.aala@oss.qualcomm.com>
@qcomlnxci

Copy link
Copy Markdown

Test results

Workflow run: 44527103277 attempt 1

Known failures configured: 0

Target Pass Non-pass Total
kbdev-glymur-crd-multimedia - ⛔ Not submitted -

Test Matrix

Test Case kbdev-glymur-crd-multimedia
LAVA result ⛔ Not submitted
Failure summary

Unexpected failures

  • kbdev-glymur-crd-multimedia did not produce a LAVA result artifact.

Result: blocked because unexpected failures were found.

Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment

Labels

None yet

Projects

None yet

Development

Successfully merging this pull request may close these issues.

3 participants